Top rated Marking Laser online provider in Ireland: Laser beam welding (LBW) uses, as the name suggests, a laser beam as a concentrated heat source to melt metals and create welds. LBW’s high power density results in small heat-affected zones. The spot size of the laser ranges from 0.2 to 13 mm which makes it suitable for welding materials with varying thicknesses, generating a better result than conventional welding process. Laser welding rapidly creates high-quality welds under fine tolerances. The process is generally automated and is used by the automotive, medical and jewellery industries. Although one might think that since oxy-fuel and plasma torches can be used for both welding and cutting, this applies to laser torches as well but this is generally not the case. A standard laser cutting head cannot be used for welding and a laser welding head cannot meet the cutting speeds and quality demanded in most industrial applications.

In many shops, the operator has to go to a tool room or supply area for a new contact tip, coil of wire or other welding accessory. This takes valuable time away from the welding cell and slows down overall productivity. To improve the operating efficiency and minimize wasted time, companies should stock at least a limited supply of all necessary items near the welding station – this includes shielding gas, flux and wire. Another helpful productivity enhancing tip is to switch to larger spools of wire such as from 25 lb. spools to 44 or 60 lb. spools to even larger packages of 1,000 lb. reels or 1,000 lb. drums. A simple switch like this means less changeover time, which adds up over the weeks, months and years. Shops should also be on the lookout for shielding gas waste. A simple device called a surge turbine can be placed at the end of the gun to provide a digital readout of the gas surge and flow rate. If the surge rate is high, investing in a surge guard can reduce the pressure, eliminating gas surges and waste. Leaks in the gas delivery system can also create a potential loss of money. By looking at the amount of consumables purchased each year and then examining the total gas purchased, a company can determine if there is a significant loss. Welding manufacturers and distributors should be able to provide average utilization figures so that loss can be detected. If there is a loss suspected, one of the easiest ways to check for leaks is to shut off the gas delivery system over the weekend. Check the level on Friday evening and then again on Monday morning to determine if gas was used while the system was in shut down mode. Discover extra details at arc welders Ireland.

How to pick a welder tips: Stepped voltage or synergic: Synergic MIG’s have the edge when you’re welding stainless & aluminium as they are pre-programmed, easy to set up & portable. They also provide a better weld characteristic and so give cleaner weld bead with less/no spatter. Inverters: Considerably smaller and lighter and so ideal for site work. All inverters are stepless and so have infinite control. Also cheaper to run power wise. Budget: How much welding are you going to undertake? Gear your purchasing decision around the jobs you will be working on the most. Polarity changeover; A lot of welders at the light industrial end will to be able weld with gasless flux cored MIG wire. Is the switchover easy on the machine you’re considering. Availability of spares & after sales service: Ask where the machine is actually made. Even the more recognised brands largely outsource their production, which can lead to quality and after sales issues with lack of continuity of supply for spares.

Here’s a lot of welder for the money. The Eastwood MIG 135 industrial Welder features infinite adjustment from 25-135 amps, enough range for 24 gauge sheet metal to 1/4-inch steel plate. It has infinitely adjustable controls and a setup chart on the case cover. It’s also spool gun compatible, giving you the option for 1/4-inch aluminum. The Eastwood MIG 135 industrial Welder mounts 4-inch and 8-inch wire spools, but the wire drive is plastic instead of metal. One other issue with the wire drive is that you’ll need to buy a drive roller if you run flux core wire instead of MIG. Eastwood included the gas regulator and hose for MIG capability, however. It’s got an industry-standard Tweco-style MIG gun for easy-to-find consumables. The connection leads could be longer, but the Eastwood MIG 135 industrial Welder is a versatile, easy to use machine for a great price. If you’re building roll cages or doing chassis work, then you’ll want the model up, the Eastwood 175 Amp MIG Welder is a great 240 volt option that includes the spool gun for aluminum capability right out of the box.

Several tips about welding equipment, MIG and TIG welders, plasma cutters. Welders with a higher power output can work with thicker metals, but higher voltage welders will require special power supply set ups—either generators or appropriate power outlets. A welder with lower voltage in the 100’s will not be able to handle heavy duty jobs, but it can be plugged in and operated from any outlet. Any welder with power over 200 cannot run off a typical power outlet and will naturally cost more to run. In addition, welders will either run an alternating current (AC) that reverses itself at regular intervals or a direct current (DC) that flows in one direction and does not reverse itself. DC offers a steady rate of energy that leads to hotter temperatures and deeper weld penetration. AC welders usually cost less than DC welders, but the available electrodes are far more limited for AC. In fact, DC welders are more costly but remain popular because their higher power offers a wider selection of electrodes and a number of working advantages such as: simple arc striking, better penetration, and improved control. Welders who expect to work on a wide variety of projects may want to consider an AC/DC combination welder.

Finally, if you’re looking for a home welder, then you don’t necessarily need the most powerful machine on the market. Some people invest in MIG welders specifically to support their home-based projects, when they’re creating something new in the garage, or working on adaptions to pieces of machinery and furniture. The Clarke MIG151EN is designed for the DIYers who can’t afford to compromise on quality. Complete with professional specifications like a non-live torch and an extra-tough protective coating on the front and rear, the Clarke turbo MIG welding machine comes with everything you need to start welding at home. There’s a thermal overload protection system to give you complete peace of mind, as well as a very powerful wire drive motor included. Additionally, you’ll be pleased to know that all Clarke products comply with the highest quality of European and safety standards. As a winner of multiple third-party awards, Clarke offers a high-performance option for anyone searching for an arc welder for home use. The rotary power selection system also means that you can choose the level of performance you need with ease. Discover more details on https://www.weldingsuppliesdirect.ie/.

The 720 Watt, 6 Amp motor spins the cutting discs up to an impressive 11,000 rpm. That’s more than enough power output to get just about any job done with a 115 mm disc. Weighing in at less than 2 kg, it’s light enough to use one-handed if you’re brave enough. For two-handed use, there’s an indestructible plastic side handle that you can screw into either side. The thing I like about this handle is the 20° angle. You get a better grip for more precise grinding work, compared with standard right-angle grips. Another bonus feature found on this grinder is the soft start. For such a powerful bit of kit, it doesn’t feel like it’s going to jump out of your hand when you turn it on. And thanks to the anti-restart function, it’s safe to use as well.

PACE Fume Extraction Systems provide effective odor reduction from the limited use of adhesives, solvents, and other compounds during handheld drilling, milling, or grinding operations. The filter cartridges are disposable, which makes them easier to use for fume extraction. Sturdy Steel Case and Lightweight Build Quality The Arm-Evac 150 comes with a steel case, which I found to be quite sturdy. It also has a dependable brushless motor that doesn’t need expensive routine maintenance. The overall unit is built with 20-gauge steel, which is ESD-safe. This tiny, low-profile machine will fit anywhere you need, and it comes with lockable casters for convenient mobility and transportation. The compact unit weighs only 20 pounds which makes it extremely lightweight.

Hougen 115 volt hmd904 magnetic drill press is one of the best mag drill machine available in the market. And also the best thing is that Hougen upgraded this drill press recently. Thus it becomes more efficient and accurate from the previous one through their continuous development and innovative designs. New attachments of this great product are slot drive arbor, which not only enhances accuracy but also enhances the change-out mechanism. Drill bit also made with sturdy material. Cutter/Mount – Rota broach or Copperhead 3/4 inch shank. Thus it can make a smooth hole. This is great for horizontal, overhead, tight areas, and getting out of another piece of steel.

Our vision and our distinct set of values drive the success and spirit of our organization. At ESAB, under Colfax leadership, we live our values. As a premiere U.S. welding equipment manufacturer, our vision and values help us to make strategic decisions, allocate resources, and focus our choices every day, domestically and internationally. ESAB offers a world of products and solutions for virtually every welding and cutting process and application. We serve industries that serve the world. The Best Team Wins – Team-oriented, involved associates are our most valuable resource, and we are passionate about attracting, developing, and retaining the best talent. Living this value is done in three primary ways: 1. Building the right team – having the right people to do the job; 2. Creating the right environment – making sure that leaders create an environment where all associates can contribute, and 3. Getting the win – when you have the right people and right environment – it makes getting the win a lot easier!

Welding Supplies Direct are the UK distributor for GPPH welding tables, manufactured to the highest standards in Europe. GPPH’s range of welding benches and tables are laser cut for precision and are used in every branch of industry. These welding tables offer perfect flatness (+/- 0.5MM) & are made from 15MM thick S355J2+N grade steel. Our modular welding benches come equipped with a hole system of all sides (tabletop & all sides); the holes are 28MM in diameter and have a chamfered edge for easy tool assembly. You have the option of standard legs or castors being fitted, too.

Forney have built a simple, mid range MIG welder that’s solid and reliable. It has some good power for the price but doesn’t have as good a duty cycle as the Hobart 190 or Lincoln 180. Forney aren’t one of the big three brands but this machine is still solidly built and I’d feel comfortable buying this. If you want a basic 220v welder without any special features, this is a good choice. Read the full review here.

Out of a huge product range of the Dirty Pro Tools, we have found a top-grade MIG welder that turned out to be so good that we have decided to add it to this shortlist. It is the tool for welding metalware of medium thickness with the output range from 50? to 60?, best for sheets up to 2 mm thick. In addition, a pretty powerful converter of this welder allows working for about 6 minutes at 50?. So, you’ll be able to weld thin pieces for a good while, and the fan will provide a decent cooling of the tool. However, when the MIG welder overheats, the red light will flash telling you to stop welding and make a pause. By the way, you can pick either of 4 available amperage settings and adjust the wire feeding speed for reliable and straight welds. We were pleased by the package that includes a face shield, a clipping hammer, a brush and a spool of welding wire, so you can start welding right after unpacking the unit. So, this Dirty Pro Tools welder is one of the most affordable models for people seeking a mid-power machine to weld fine metal sheets.

UK market dive: Like LOTOS Technology and LONGEVITY Inc, Everlast has a little over a decade in experience. It is a California company which was founded in 2004. The light and efficient Everlast welder has one of the best duty cycles on our list. With the most basic of designs, this Everlast power-mig welder is perfect for novices. Along with other welders with 4, 7, or 10 voltage settings, the Everlast has infinite settings for voltage and also wire speed, making it a customizable experience. The Everlast 140amp MIG welder can cut mild steel, stainless steel, as well as chrome-oly at a thickness of 3/16 inches. It can be used with both four-inch and eight-inch wire spools. It’s incredibly lightweight for the power it gives out.

Use the Personal Protective Equipment (PPE): It is mandatory to use various appropriate PPE while handling an industrial gas cylinder. For instance, wear safety glasses, safety shoes, gas masks, and safety glasses, while working with cylinders filled with compressed gases. Similarly, it is important to use flame arrestors when using acetylene cylinders in compressed air. Use Regulators Properly While Handling Cylinders: Regulators are devices, which are designed to lower the working pressure of the gas. These devices differ according to gases. Many times, the regulators aren’t handled and stored properly. This improper usage may lead to problems in the long run. Hence, it is important to take several precautions while using regulators.

Do you feel frustrated because the disc grinder work is not progressing well, or you are running out of time? If that is your problem, then this Metal Cutting Disc will help you. It is a high-quality product that has been designed to provide ultimate performance. The wheels are made of steel and have a tooth count of 25. They are great for concrete, metal, or other materials where you want to cut through tough materials quickly. These discs are made from high-quality cutting wheels with a flat shape. They have a 3? diameter and a 1/16? thickness. With ultra-thin metal and stainless steel, they can quickly and easily cut through burrs and other unwanted materials. With these discs, you can grind metal and stainless steel fast and smooth while minimizing noise. As a versatile option for workshops, the discs can be used with sheet metal, die grinders, air cut off tools, and electric cut off tools.